I’m loving the wide leg pant trend, so when I found the Walk Boldly Wide Leg Pants Pattern from Pattern Emporium, and saw that it was designed for knits, had no zipper, and a high-waist option with darts, I knew I had to give it a try. This is my first time using a PE pattern, and it was a great experience. The pattern was well illustrated and included a number of useful tips, including a good tip on sewing darts.
I used a premium black 12 oz rayon/nylon ponte fabric from KnitFabric.com. The ponte has about 30% stretch across the width. Although the website said it only had 2-way stretch, I think it has about 20% stretch in the length as well. It is a hefty fabric with a nicer drape than the other ponte fabrics in my stash. It is sold out in most colors now, but I may grab more in whatever color they have left (mustard perhaps?).
The pattern comes with two waist heights and multiple pocket options. I made the high-waist version, which hits right above my navel. I made the jeans-style front pockets and added an extra two inches to their length to make sure my phone would fit comfortably when I’m seated. I also made the back patch pockets, because I can always use more pockets and I think they’re cute. The pattern uses AU sizing, I normally would select a 4P or 6P for pants, but the size chart said I should go with a 10. The pattern doesn’t come in petite or tall sizes, but it does offer short, regular, and tall pants lengths (which means the only thing that adjusts is the length of the leg, but I often prefer the fit of short pants rather than petite pants so this works for me). I cut out the size 10 in the short length, which is meant for those who are 5’3″ tall. I’m closer to 5’2″ and the pants would have been about 1 inch too long (which makes sense) if I used the recommended 3/4-inch hem. So I did a chunky 1 3/4-inch hem instead. The size 10 fit perfectly, as you can see in the photos below (modeled with a bishop-sleeved Bondi from Sinclair Patterns).
I’m very happy with these pants. I’ve seen similar pants from major retailers this season, only most of them don’t have the back darts or the back pockets, which take these pants up a level. These are stylish, practical, and so comfortable to wear! I did have to add seams to the sides of the waistband to prevent the elastic from rolling.
My young adult daughter told me she loved the high waist and said I should tuck my shirt in to make my (short) legs look longer. She also recommended I try the Walk Boldly pants in a bolder fabric. So I selected a polyester/spandex “haute pink and umber plaid yarn dyed jacquard knit” from my stash (purchased from Surge) for bolder Walk Boldly pants. These are indeed a much bolder statement (although the haute pink is tastefully muted). Even one of my male co-workers yelled out “nice plaid pants” as I walked by his office.
Every time I use plaid fabric I get a frustrated because I want my plaid to match perfectly and it never quite does. Knit plaid fabric is particularly difficult to match because if it stretches just a little bit when you cut it or sew it, the plaid won’t match. There are some spots on these pants with fabulous matching that I am very proud of. The back pockets cannot geometrically have a perfect match due to the darts, and yet they match about as well as they could. The outside seam of the right leg is magnificent! The other seams are not as closely matched, and the matching in the front crotch area is particularly disappointing. But I’m not going to let that stop me from walking boldly and without worry (More on plaid coming soon!) Now I’m looking forward to making more of these pants (but probably not in plaid) in a lighter weight fabric for spring and summer.
The pink plaid pants look great with a black top, but I happen to have some cuddly versailles brushed hacci sweater knit (also from Surge) in my stash in something that seems pretty close to me to umber (officially the color is “sienna”), so I decided to make a trendy cropped sweater to match. This hacci is brushed on the inside so it is super soft against your skin. I decided to try the Sweet Cheeks Sweater pattern from Pattern Emporium, which has dropped, full sleeves that are gathered and cuffed at the bottom. It comes with several neckline and length options (including an ultra crop), and a super cute split banded bottom. The size chart suggested I should cut a size 8, but also suggested sizing down for less of a closer fit. So I sized down two sizes and cut a size 4 in the cropped length with the mid neck. This was another great PE pattern. I especially like the tips for gathering the sleeve and attaching the cuff. I will probably make more of these sweaters too in other fabrics with exactly this configuration, but may also try a longer length and the V-neck.
First I made bishop Bondi for myself using sangria microsuede jersey knit from Surge Fabrics. This is a soft polyester-spandex jersey knit with 50% horizontal and vertical stretch. It is not very thick, but it still has a warm, cozy feel to it on the inside. It was easy to work with a drapes very nicely but has a terrible tendency to be clingy. It behaved a little bit better after I sprayed it with anti-static spray, but it was still more clingy than I would like.
I made the Bondi in my usual 4P size with my usual hip adjustments and screwp neck. The bishop sleeves are cut wide at the wrist and gathered before attaching cuffs. I used a long stitch on my sewing machine and pulled the threads to gather. I sewed on the cuffs to the sleeve with my serger. This is not in the instructions, but I stretched the cuffs after they were sewn on to pop the gathering stitches and then pulled out the loose threads. I figured that would inevitably happen when I wore it so I might as well do it now and keep the cuffs nice and stretchy. I love both the look and the feel while wearing of bishop sleeve cuffs made from a folded piece of knit fabric.
I made the second bishop Bondi for my mother. I had extra ITY fabric from a Joanne dress I made last year with a beautiful blue swirly pattern that I love. My mother has commented multiple times how much she likes that fabric so I decided to use it to make her a top. This was the first top I sewed for her and I sewed it based on her measurements. She doesn’t live near me so I wasn’t able to check the fit until she tried it on later. She reports that it is very comfortable and the fit is perfect!
I was so happy with the way my mother’s bishop Bondi came out in ITY fabric that I decided to make myself one. I have a purple suit (I didn’t make it, but I bought it on sale from Banana Republic Factory and tailored the pants myself to fit better) and have been looking for a print blouse to wear with it. I scoured lots of online fabric stores for a nice ITY print with royal purple in it. I found this print at StylishFabric.com, an online fabric store I had not previously noticed. My bishop Bondi goes perfectly with my purple suit and is much more comfortable wear with a suit than a traditional woven, button-down blouse.
I love these bishop-sleeve tops and I’m sure there will be more! See also the Lakeisha top I made for my daughter, which has bishop sleeves too.
A few weeks ago I made a Sinclair Soho dolman v-neck sweater from a marled dark green sweater knit. It was easy to make and super cozy. I’m wearing it a lot, but I have one complaint: I feel the sleeves attach at a rather awkward spot, which on me is too close to the elbow. I think the sleeves would look better and be more comfortable if they seam were moved up closer to the top or eliminated completely. So for my latest Soho I hacked the pattern a bit and extended the front and back bodice to include the sleeves. I basically just took the sleeve pattern piece, (digitally, in Affinity Designer) cut it in two and attached part of it to the front bodice and part to the back. I shortened the sleeves by .5 inch to account for not needing the seam allowance, and then I shortened them by another full inch because the Soho sleeves are a bit too long for me. I ended up cutting the two bodice pieces with attached sleeves on the fold, which I can do because I was using 58″ fabric and I’m a size 4p. So I just had a top-length front, back, neck band, bottom band, and pockets to cut. I cut the whole thing out of 1.5 yards of fabric.
I made a few other minor modifications to the pattern, including grading out the lower few inches of the bodice and extending the bottom band to be the same size as the bottom edge of the bodice so that the bottom of the sweater would be looser and not cling to my hips. I made the pockets about an inch deeper to make sure they would be deep enough for my phone and so that I could anchor the pockets in the seam attaching the bodice to the bottom band. (I usually don’t pass up any pocket opportunity and often add or enlarge pockets, but I didn’t include any pockets or bottom band on the green soho as I made that as a regular knit sweater top.)
I used the interwoven squares quilted knit fabric in the clematis color from Surge Fabric Shop. This is a 60% cotton, 35% polyester, 5% spandex knit with a cool pattern, reminiscent of the tumbling blocks quilting pattern, that looks like interwoven 3D cubes (or just a bunch of upside-down or right-side Ys depending on how you orient it). I love the fabric, but it wasn’t quite what I expected when I ordered it online. Based on the photos on the Surge website, I was expecting a brighter, pinker purple, similar to the boots I’m wearing in the photo. In reality, the color is more of a dusty violet. In fact, it almost exactly matches the grape brushed sweater knit I also bought from Surge. (To be fair, this is a tricky color to photograph in indoor light. My initial indoor iphone photos of this fabric looked very pink and I had to futz with the color in my photo editor to get an accurate representation. The color looks more accurate in my outdoor photos, which I did not color correct at all.)
I also didn’t fully understand that the fabric is actually quilted. I was assuming it was a quilted look, but actually it is three layers of fabric joined together. The top layer is where all or most of the cotton is, and it feels very soft. The bottom layer is a smooth polyester, and the middle layer is a fluffy polyester that looks dark purple like quilt batting. The result is a very warm and snuggly fabric on the outside that is fairly smooth on the inside. However, I did not realize that when I cut it, purple fuzz would start to seep out of all the cut edges. It’s not a huge problem, but it does mean you should be prepared to cut away fuzz balls as you sew and fold under or overcast all of the raw edges.
The end result is soft and cozy and looks great. The v-neck looks awesome and the pockets and band look pretty good. The fabric is heavy enough that there is no way to make the pockets completely invisible, but with the understitching, they tuck in pretty well and don’t look bulky, even when I put stuff in them. I felt pretty warm wearing this outside over a cotton t-shirt on a chilly winter day while my photographer was bundled up in a parka.
When I saw the new Ellie & Mac Lakeisha Cottage Dress pattern released a few months ago, I knew my 17-year-old daughter would love it. The pattern includes multiple sleeve and skirt options, as well as instructions for making a peplum top or crop top. It also includes instructions for a variety of modifications.
My daughter asked for a longer version of the crop top with bishop sleeves and selected a maroon midweight soft polyester rib knit from my stash. I followed the suggestions from pattern tester Lindsey and added five-inches to the bottom and curved out the side seam about 1 inch to turn it into a top that could be tucked in. I hemmed the bottom rather than adding the elastic. I used 1/4-inch elastic rather than 3/8-inch elastic around the neck, because that’s what I had. Otherwise I followed the pattern as written. The instructions for choosing a size were good, and the bra-cup sizing for the upper bodice front worked well.
My first attempt at sewing the upper bodice to the bottom bodice and clear elastic with my serger was a complete disaster, and rather than unpick the seams from those two small pieces, I cut them out again and started over. Getting the gathered top bodice, elastic and bottom bodice aligned under the serger needles was tricky but I succeeded the second time. I think it would probably have been easier with a smooth (not ribbed) fabric. After I figured that out, the rest of the top construction was fairly straight forward. I sewed most of the seams on my serger and used my sewing machine to sew the basting stitches for gathering, the elastic casing, the bottom hem, and the sleeve cuffs. I was going to use the serger for the cuffs but they are quite narrow and there wasn’t enough room to maneuver so I used my sewing machine.
My daughter is very happy with her Lakeisha top! She especially likes the big bishop sleeves, which work really well in the rib knit.
My past attempts at knitting a sweater ended badly. Some day I may try again, but for now I’m just really happy to buy fabric that has been knitted on a knitting machine and sew it together into a sweater. Today I will show you two sweaters I sewed, both from Sinclair patterns.
I sewed my first sweater last spring using the Sinclair Loop drop shoulder knit top pattern. I used a lightweight black and white polyester sweater knit from Cali Fabrics with 2-way 100% stretch. I sewed it with the basic sleeves, medium scoop neck, and long-line high-low split hem. The pattern has lots of options for sleeves, and even a kangaroo pocket, but I stuck with the basics. The best feature is the split hem, which looks complicated, but is very cleverly designed so all you have to do is cut out the right shape, sew it together, turn it around, and a lovely tailored split hem with a beautifully mitered corner just pops right out.
This week I sewed a warmer V-neck sweater using the Sinclair Soho dolman relaxed style top, tunic and mini dress pattern. While the Loop and Soho are both fairly relaxed and have sleeve seams that aren’t right at the shoulder, the Soho drops the seam all the way to just above the elbow and has a wide curve through the arm pit. The bodice also has a little bit of shaping. The loop is a boxier fit. For the Soho, I used a very soft and fluffy marled hunter green brushed rib sweater knit from Surge Fabrics made from polyester, rayon, and spandex. It has a 75% horizontal stretch and minimal vertical stretch.
The pattern can be made color blocked, with diagonal stripes, with pockets, with or without a back V-neck, with or without a bottom band, and at various sleeve and hem lengths. I made the most basic version in the regular top length without any pockets, color blocking, bands, or back V, and I cut the front and back on the fold rather than with a center seam. I considered having the ribs run diagonally (check out some fun diagonal stripe looks on the Sinclair website), but was concerned about how it might hang with a lot of horizontal but not vertical stretch, so I took the easy-peasy approach. The ribs run vertically on the bodice and also on the bottom part of the sleeves. I cut out the bottom band but decided not to use it, so I made it into a matching headband.
This pattern sewed up very quickly on my serger (in a couple of hours). The only bit of trickiness was the V-neck. I had never attempted a V-neck before. The pattern has great instructions, although it took me some time to get my head around them. Now that I did it once, it will be even easier next time around. The fact that I was dealing with a very stretchy fluffy knit made the V-neck a bit more challenging, as the instructions call for making a very sharp point at the center of the V, which was hard to do with this fabric, but I got it done. I can see grafting this V-neck onto other patterns too, for example to make a V-neck Loop. It is a fairly low V on me so I might raise it a smidge or shave half an inch off the center seam/fold line.
I did have to shorten the sleeves by about 2.5 inches before I hemmed it. Looking at photos from others who made the long-sleeved version, it looks to me like most of them have sleeves that are a couple of inches too long. That might be the intended slouchy style, but I prefer sleeves that don’t go past my wrists.
The sweater if very soft and comfortable. The fabric feels very light but it is actually quite warm and cozy!
I look forward to trying other variations of the patterns in different sweater knits, and maybe even trying some color blocking or making a longer length for a tunic or sweater dress.
A while ago I made a bunch of ties and never got around to blogging about them. Here they are. Details on pattern below.
I previously had commissioned a tie-seller on Etsy to make some ties out of my bad passwords fabric. But she isn’t on Etsy any more so I decided to try sewing some times myself. There are lots of tie patterns available online, some of them free. Most require a main fabric, interfacing, and lining, and require some hand sewing along the center back seam. So I was excited to find Bryanna’ Free Neck Tie Pattern and Tutorial that was super easy and can be made without any interfacing or hand sewing (except for tacking down the tie keeper ribbon on the back). I tried it and it was great, but when I came back later to find it I saw that Bryanna had taken down her sewing site some time in 2023. Fortunately, you can still view her tutorial using the Wayback Machine. Unfortunately, you cannot view her pattern. But I had previously saved it and hacked it a bit. So I will share my hacked version of it here.
First I merged the multi-page file into a single page, suitable for projector sewing. For those of you who are printing out your patterns on 8.5×11 pages, sorry this may not work for you. You may be able to print it tiled. The pattern calls for cutting the tie in two long strips diagonally (on the bias). The front is much longer than the back and requires a really long piece. This minimizes the number of ties you can get out of a yard of fabric. The long front piece is also too long to easily project. So I took a segment of the tie front and moved it to the tie back. In my hacked pattern you can see the segment and you can put it on the front or the back as you see fit. Just don’t put it in both places or you will end up with an extra long tie. You do end up with a seam where the front and back connect, but in my experience, even in my hacked short front, the seam does not end up in a visible part of the tie when being worn.
The great part about this pattern is you layer your main fabric and your lining, fold them, and sew the whole thing together in one long seam on your sewing machine. You then turn the whole thing inside out in step 7 and you are basically done. The tricky part, is in the turning the whole thing inside out with a safety pin. You have to feed the thick part of the tie through the narrow neck, and that is not all that easy to do. Just take it slowly and you’ll get there eventually.
Bryanna suggests folding the ends of a 3″ tie keeper and hand sewing them in place. Instead I recommend cutting a 4.5″ tie keeper, folding it in half, and sewing it into the main seam of the tie as part of step 6 (just the ends will be sticking out of the seam at the end of step 6). After the tie is turned right side out in step 7, you will have a tie keeper tucked into the seam, with no raw edges. At that point you just need to flatten it out and stitch down the sides. I think it looks a little neater this way.
After I made a few password ties, I found the cookie fabric and decided to make a tie for my student who was presenting our research paper on cookie consent banners at a conference.
I finally sewed something for my husband. Sinclair has a bunch of men’s patterns and the sewists in the Sinclair Facebook group often post smiling photos of their husbands and sons modeling their creations. After Chuck recently went through his drawers and removed a mountain of old long-sleeve t-shirts with holes in them, I decided to sew him some new ones. He loves striped shirts, so I have been on a quest to find good yard-dyed striped fabric in t-shirt weight knits (which is surprisingly difficult, pointers to good sources welcome).
I selected the Sinclair Kai semi-fitted crew neck t-shirt for men pattern. This was very easy to sew and is essentially the same as Sinclair’s Bondi t-shirt pattern for women, but with a different cut and sizing. The instructions for measuring and fitting were clear. I ended up making only a minor adjustment, grading between two sizes on the lower half of the bodice, but the pattern offers instructions for addressing more difficult fitting problems. I also shortened the sleeves and the bodice by about 1.5 inches before hemming. With my serger each of these shirts took only a couple of hours to sew.
For my first Kai, I selected Surge’s Sedona mini stripe jersey in Tuscon sun (a gold color). It is a lightweight stretchy fabric that is a blend of rayon, cotton, polyester, and spandex. It’s great for drapey summer-weight tops (maybe a summer cardigan), but ended up being a little too light and slinky (as Chuck put it) for a long-sleeved men’s t-shirt. It works fine as an under layer, and he was seemed happy with it none-the-less.
For my second Kai, I selected a stretchy rayon/polyester/spandex yard-dyed rib knit in navy and olive. This fabric is also fairly light and drapey, but it is more substantial and has a more suitable weight for a long-sleeved men’s t-shirt. I like this one better. This fabric was fairly easy to sew with, but I found it almost impossible to mark notches with my washable markers, so I ended up improvising the collar band a bit. I probably should have marked the notches with clips.
I think he enjoyed being photographed rather than being my photographer this time. I was excited about using the fall leaves as a backdrop but he was more interested in a photo with our new car.
I’ll make some more Kai t-shirt for him after I find some good cotton-lycra striped fabric.
I love my Pylos LiKnit palazzo pants made with my adaptation of the Sinclair Cleo pattern, but they are more of a summer weight and not so good for our chilly Fall weather. So I made a new pair in black Surge’s stretch velour corduroy last week. This is a somewhat slinky corduroy, very soft and a medium weight and horizontal wales. It makes for a super comfy pair of Fall pants (with pockets, of course!), perfect to wear with a chunky sweater. When it gets colder I’ll probably wear tights or leggings under them. Wide-leg pants are very comfortable and cool in the summer because they let the air flow, but that’s less desirable for cold-weather wear and thus may require layering. But either way, these pants are comfy like my pajamas.
I sewed the pants using the same adaptations of the Cleo pattern I used previously, and lined the waistband with Surge’s black quad performance jersey knit. To keep the tops of the pockets from sagging I sewed a strip of clear elastic into the seam allowance of the diagonal seam at the top of the pockets.
I’m also wearing a Sinclair Bondi shirt here I sewed last year and never got around to photographing. This is a grey cotton-lycra fabric. I tried a binding rather than a band on the neck for this one.
I’ve been holding onto this fabulous ivory and black geometric polyester double-knit fabric since last spring, with the plan to turn it into a long-sleeve Sinclair Valley Knit Skater Dress. The fabric has some body (and just barely enough stretch for this pattern) and a nice drape, so I decided to use the full-circle skirt from the add-on pack for a skirt that would naturally poof out. Unfortunately, I didn’t have quite enough fabric, so it took some tetrising to cut it all out (with my projector), and I ended up having to split two of the skirt panels in half and turn the long sleeves into 3/4 sleeves. But by splitting the skirt panels I was able to avoid a seam in the center front of the dress.
I made the pattern mostly as written, lengthening the bodice as recommended when omitting the waistband. I also used my Bondi screwp neck modification, as I have done for my previous Valley dresses. This time I sewed the pockets to the waistband as the pattern suggests, since this is a pretty stable knit and I wasn’t worried about the pockets getting pulled down. I did lengthen the pockets by about an inch to reduce the risk of my phone falling out. The pockets on the finished dress are great and with the full skirt they are nearly invisible, even when full.
This is the first Valley I sewed with a serger, and it went very quickly. It only took about 3 hours to sew after cutting the fabric. Of course, it took a while to hem the 13-foot circumference full-circle skirt. But my teen daughter approves and says the full-circle skirt was definitely worth the effort. Indeed, this is a dress that really is fun to wear.
Back in August I tried out the Pietra Pants and Shorts pattern from Closet Core Patterns. A friend made a couple of pairs of these pants and the pocket design immediately caught my eye.
Closet Core does not seem to offer projector files, so I used their copyshop pattern, designed to be printed on two A0 pages. I used Affinity Designer to select the layer for the size I wanted, thicken the lines, copy and paste the pieces onto one large page, and rotate them all in the correct direction for cutting. This was pretty easy to do.
The pattern did not come in a petite size, but as I like high-rise pants, the only modification I thought would be needed for my short stature was to shorten the pants. I cut out size 6, but shortened the bottom hem of all the pieces by 4.5 inches. I made view A, the wide leg pants. There are also instructions for tapered leg pants and shorts.
Although the pattern was designed for lightweight woven fabrics, I used Pylos Liknit fabric, which is actually a knit fabric. But having used Liknit for two other pairs of pants, I knew it doesn’t stretch a lot and is fairly stable, so I decided to treat it as if it was woven. I used the linen colorway. The main part of the Pietra pants that you don’t want to stretch is the front waist band, and since that is interfaced, there wasn’t any issue with unwanted stretching. I think this fabric worked out well for this pattern. But I had a lot of trouble with the back of the waist band and it is possible the fact that it wasn’t actually a woven contributed to the difficulties I had, but I’m not sure.
The instructions were clear and easy to follow for the most part and the pattern is nicely drafted. The pocket and waistband are a bit tricky, and some of the construction is not completely intuitive. However, I found if I carefully followed the instructions, used the diagrams, basted all the seams where the instructions recommended basting, and matched all the notches (I marked the notches on my fabric with my trusty Crayola washable fine-point markers), it all came together the way it was supposed to. The result is a very clean and professional look in the front. I topstitched the front leg seams, which was optional, but I thought it gave a nice finished look.
I sewed all the seams with my regular sewing machine at 5/8 inch as instructed, and trimmed to 3/8 inch and serged in one step with my serger. This is only my second serger project and the first one with any major amount of trimming, so I’m still fascinated by watching the trimmings slide into the bucket. The pattern didn’t specify trimming on the inner our outer leg seams but I went ahead with that as I had for the other seams.
Everything went really well until I got to installing the waist elastic. For a size 6, the instructions said to use 12 inches of 2-inch wide elastic. I attached one side and pinned the other and tried on the pants. The waist was way too big. I pinned the elastic shorter, but the front of the pants pulled to the back. I decided some grading was in order. I unpicked part of the inner waistband seam so I could grade both sides of the waist by .75 inches, bringing the new line of stitching down about 6 inches to right above the pockets. I probably could have graded it even more. Then I shortened the elastic to 10.5 inches and sewed it into the waistband. The instructions direct you to sew two parallel rows of stitching in the back waistband, through the elastic, while stretching the elastic. This was easier said than done. I could have used some more hints about how to achieve this. In the end I got it done, but my back waistband looks messy. That said, even if I had sewn it well, I think this style of gathered waistband would look messy, and it pulls the front more than I would like, which is not very flattering. With an untucked shirt it looks much better.
The instructions call for a 2-inch hem, but I ended up doing a 2.5-inch hem to get it to the right length. Of course, I could have trimmed .5 inches off before I hemmed it.
The pants didn’t take that long to make and they are very comfortable to wear. I love the fit of the high waist, but I really don’t like the look of the back waistband, and the way the elastic pulls the front in, it ends up not being all that flattering against my tummy. As long as I keep my shirt tucked in, I think the pants look pretty good.
I’m apparently not the only one who has had some trouble with the elastic waist. Closet Core offers instructions for adding a zipper, and other bloggers have reported having to redo the waist with darts. I think the elastic works better on some figures than others, and may also work better with some types of fabric. I considered adding a zipper, as suggested for those with smaller waists in proportion to hips, but figured it would make these otherwise comfy pants less comfortable. So Instead I decided to unpick the back waistband and chop off the top 2 inches of the pants so I could add a yoga waistband. It was a shame to cut into the beautiful finished front panel, but this seemed like the best way to turn these into pants I would actually wear.
I constructed a 3-inch yoga waistband using the Sinclair Cleo pattern I have used successfully for other Liknit pants. Since the Liknit has some stretch to it I was able to make the outside of the yoga waistband in the same fabric as the rest of the pants. I used beige QUAD Performance Jersey Knit for the inside of the waistband for a nice snug fit and didn’t add any elastic. I basted the waistband in place, tried it on, unbasted, made some adjustments, rebasted, tried it on again, and then surged the waistband to the pants. I topstitched the seam in place.
I think the pants look a lot better now. I still love the Pietra pockets and the front leg seam, but now the waistband looks good too. I might make another pair in another fabric (maybe a ponte) with the yoga waistband modification, perhaps only 2 inches next time. By the time I got around to doing this modification the Fall weather had kicked in so it is getting a bit chilly here for such light weight pants, but I expect I will wear them a lot next summer.
I feel strongly about pockets. When I sew my own clothes I make sure they have pockets large enough to hold my stuff. It is very frustrating when I buy ready-to-wear clothes with inadequate pockets. I’ve seen blazers advertised as having “adorable faux pockets” that make me want to scream. There is nothing adorable about faux pockets. But even worse, perhaps, is buying a pair of pants with pockets, only to find out that my phone does not fit in them, or that it fits but slides out every time I sit down. My husband can fit his phone, his wallet, his keys, a tube of chapstick, some change, and other odds and ends in the front pockets of every pair of pants he owns. I should be able to do that too!
What about the back pockets? Pocketing a phone in a back pocket may be ok while standing, but on me, back pockets are usually placed such that I end up sitting on my phone, which can be uncomfortable or cause the phone to fall out of my pocket. Plus, putting valuables in back pockets makes you more of a target for pick-pockets.
With pleated pants, a phone can often be completely concealed in a front pocket if the pocket bag is deep enough. However, with tight fighting pants made of stretch fabric, it is hard to avoid a phone bulge. I can sometimes fit my phone in the pocket horizontally, but it produces a bulge across my stomach that isn’t very flattering. I personally prefer to see that bulge further down the leg or more on the hip, but that requires deeper pocket bags.
I have started seeing some women’s pants advertised as having “utility” pockets. The best I can tell these are special pockets that are actually large enough to be used. Shouldn’t all pockets have utility?
I have started retrofitting the pockets of my pants that otherwise fit well, adding pocket bag extensions. It’s actually not that hard to do. Here’s how I augmented the pockets bags of a pair of black dress pants recently.
Here’s the pants turned inside out. You can see that the original pocket bag is big enough to hold a credit card and not much else. My cell phone fits, but as soon as I sit down it slides out.
To improve this situation, the first step is to figure out how much you need to add to the pocket. I like my pockets to be long enough so that my phone will sit entirely below my hip crease when I’m sitting down. If my phone sits above the crease, it will fall out. If it sits in the middle of the bend, it will be uncomfortable to sit down. For this pair of pants, the pocket bag needed to be about 3.5 inches longer. So I cut 4 pieces of fabric 6 inches wide by 4 inches tall. You can use any sort of lightweight fabric for this. Generally people use woven fabrics for pocket bags. But I used some ITY with a little bit of stretch for these pants, which can be a little more forgiving as you sew.
The next step is to turn your pants inside out, slit open the bottom of the existing pocket bag, and pin one piece of the new pocket bag material to the inside of the old pocket bag. If the bottom of the pocket bag is rounded, you may want to square it off. I think it works best when the seam is on the outside of the pocket so nothing catches on it when you put stuff in the pocket. Once the pocket piece is pinned, carefully sew it on. This requires some tight maneuvering with the sewing machine. Alternatively, you can use a fusible tape to fuse the old and new pocket pieces together, and then zigzag to secure.
Then pin an sew the other new pocket piece on.
You will then have a pocket bag with two flaps on the bottom. It is not a very useful pocket at this point because it is completely open at the bottom. The next step is to sew around the three open sides. If the original pocket is anchored in the side seam of the pants, you can attache the pocket bag extension to the side seam too.
And that’s it. Now you have and extended pocket big enough to actually hold your stuff. Once you have sewn a couple of pockets this way, you will probably be able to do it without any pinning. It is important to realize that without a lot of unpicking, it is nearly impossible to make all the seams line up perfectly due to the limited space you have to maneuver, but it doesn’t really matter. As long as your pants are not see-through and any gaps you have are not so big that anything is in danger of falling out of your pocket, nobody is going to see the gaps in the pocket bag inside your pants and it will not impact the functionality of the pocket.
Here are two other pants with extended pocket bags: a pair of pleated flannel dress pants and a pair of wide-leg stretch cords. I used scraps of quilters cotton for these. The grey pants only needed a small extension, but it made a huge difference in having my phone sit comfortably and not fall out. When I wear this pants with a phone in my pocket, you can’t really tell. The cords needed a longer extension, Although these are wide-leg pants, they are fairly tight at the waist. With the original pockets, my phone produced that ugly waist bulge. Now the phone sits just below my hip crease — it is still visible, but I think it looks better there.
It’s made from a luxurious custom printed crushed velour fabric from Contrado. It’s vibrant and shiny, especially in the sun. And it feels stretchy and soft and is the most comfortable ball gown ever. All of my past custom password fabric orders have been from spoonflower.com. But they didn’t offer a suitable fabric that was both dressy and stretchy, so I started looking for other custom fabric vendors. Contrado is based in the UK so I was a little bit uncertain about placing an international order, but they offer a ton of fabric options so I ordered a fabric swatch kit. A few days later I opened an envelope with more fabric swatches than I knew what to do with. I didn’t count them, but I think there were over 100. So many fabric choices! I dumped them out on the floor and tested each one for light weight, softness, and stretchability, narrowing down the pile to a short list of scuba variants and crushed velour. They were all nice, but I loved the feel of the crushed velour and the way it catches the light. So with that in mind I ordered some cheap crushed velour to make a muslin of the pattern I intended to make (Sinclair Serena), but at a shorter length. The cheap crushed velour did not feel luxurious at all, but it made a nice dressy summer dress that I have worn several times this summer.
Once I had picked out the fabric and settled on the pattern, I worked on the fabric design. I took the PDF file for the Serena dress in the size 4 petite, and extended the skirt length to be long enough to graze the tops of my feet after hemming. I then created a PDF file the width of the fabric (53.15 inches) by 108 inches long in Affinity Designer. I pasted the Serena pattern pieces into the file, mirroring those that needed to be mirrored. The skirt back at that length was wider than 53 inches, so I decided to add a back seam and print the skirt back in two pieces. I split the skirt back and added a seam allowance to the center back seam. The skirt front is not as full so it fit the fabric width without a problem. I made all the pattern lines red and deleted all of the internal pattern markings, keeping only the outlines. Then I added a solid purple layer under the pattern pieces. The next step was to add all the passwords to the dress. I started with my previous password dress fabric and cut and pasted the passwords inside the pattern pieces (removing the naughty words this time). In some cases I rotated them or scaled them slightly from the previous design. I spent a lot of time rearranging the passwords to fit them all into the puzzle. I also chose some of my favorites for prominent placement. I decided to cover the entire skirt and back of the bodice with passwords but leave the bodice front solid purple.
I could have continued futzing with the password layout for quite some time, but I was not sure how long it would take for my order to be delivered and I had a deadline for finishing the dress, so I saved a giant jpg file and called it done. (I subsequently spotted several small glitches but hopefully nobody else will notice.) I went ahead and placed the order on a Sunday morning in August. Much to my amazement, the fabric was printed in the UK, shipped across the ocean, and was delivered via FedEx to my doorstep in Pittsburgh, PA just TWO DAYS LATER on Tuesday! The custom fabric is expensive. Even with a discount coupon it was $42 per yard. But I paid only $9.95 for standard international shipping.
The Contrado website said the fabric would be machine washable, but was a little vague on whether to expect shrinkage. Given that it was 100% polyester fabric I took a chance that there would be minimal shrinkage (definitely a risk if you print your pattern pieces directly on the fabric) and I was right.
I laid the fabric out on my magnetized cutting mat and cut it out along the red lines with my rotary cutter. I knew from sewing the muslin that crushed velour is slippery and hard to pin in place, so I did a lot of hand basting and then serged most of it, leaving the cutting knife retracted so I wouldn’t accidentally cut anything I didn’t want to cut (since the pattern had 1/4-inch seam allowances there wasn’t really any need to trim as I sewed). The first few steps of the bodice assembly went pretty well, until it came time to join the F1 piece to the F2/F5 piece of the bodice. There are multiple points to line up and after basting and unbasting multiple times I realized that there was no possible way to get everything simultaneously lined up. After about three hours of this I finally gave up and sewed it together so the outside looked good, but the inner lining (purple ITY) looked like a train wreck. But nobody will ever see it, except for the fact that I am showing you this photo right here so that you can see that the inside is a complete disaster but the outside still looks really good. You will see there is a diagonal piece that goes from the top left to the bottom right. There is another diagonal piece that starts in the middle and goes to the bottom right. Those two pieces are supposed to be sewn together on top of each other, but yet there is a bout a 1 inch gap between them. So that nothing would be flapping in the breeze, I sewed the loose edge to the inner lining. I believe the problem has to do with the fact that my fabric stretches only in the horizontal direction and has almost no vertical stretch (going against the advice of the pattern maker). The fabric I used for my muslin was similar, yet somehow I did not end up with this particular problem. I’m perplexed, but it all worked out in the end.
Of course, I chose the pocket option, since Cinderella and I always need pockets, even when we go to a ball. I decided to make the pocket bags out of the purple stretch velour so that they would not show if they fell open. Stretch velour is not really ideal pocket bag material, especially since I stitched the pocket openings up a bit to prevent things from falling out. Sticking my hand in a pocket tends to cause the pocket bag to come out with my hand, but it works well enough for holding my phone and a small wallet. From past experience with this pattern, I know that I prefer the pockets to sit a bit higher than the pattern calls for so they don’t jiggle around when I walk, so I ignored the marks and just tried on the partially completed dress and pinned the pockets where I wanted them to go.
I’m really happy with the end result. It is exactly what I wanted. I was so excited that I put it on and made my husband follow me around my yard with my DXLR camera while I played fashion model and posed for photos. He has no formal photography training but he is starting to get the hang of fashion photography as I explain to him that there is a difference between zooming in and moving closer to the subject.
Did I mention that this dress has some twirlability?
Ok, so why did I make this dress? Well I’m the director of the CyLab Security and Privacy Institute at Carnegie Mellon University. This is our 20th anniversary year and we held a gala to celebrate on Tuesday. Obviously, I need a password ball gown to wear to the gala. (And of course my husband needed a matching tie.)
As an added bonus, the Carnegie Science Center held their Geek Out Gala on Thursday, and this was the perfect outfit! So many people I didn’t know came up to me to talk with me about my dress.
My husband is a big fan of Mexican green tomatillo salsa. As I was struggling to grow vegetables in our small Pittsburgh yard, he suggested I give tomatillos a try. I was skeptical, but I got a couple of tomatillo plants and planted them by the driveway. One flourished and the other did not. I read that you need to have at least two tomatillo plants for cross pollination, so I bought another and soon I had two plants full of tomatillos and later in the season we made salsa. Over the years my tomatillo farm has expanded, and now it takes up a good chunk of the garden above my retaining wall. The plants seem to do well in Pittsburgh weather, and for whatever reason, the critters in my garden seem to mostly leave them alone. I’ve learned to let them grow in pots on my deck until they are about 18 inches high so the young leaves don’t get devoured by beetles. And spraying them with insecticidal soup also helps keep the bugs away. Once they get to about two-feet tall, they seem to do fine. I typically plant about 6 of them now, and I get a few volunteers growing besides them.
By August, my tomatillo farm is a mess. Most of the plants have outgrown their cages, and some have toppled over and resist my efforts to upright them. This year the adjacent tomato plants have taken over, with lots of volunteers as well. Note to self: next year pull out most of those volunteer tomatoes!
Tomatillos grow in little husks. They are ready to harvest when they fill their husk. Sometimes you can tell they are ready because the bottom of the husk has burst open, revealing bright green or purple fruit. Sometimes you have to gently squeeze the husk to figure out whether it is full. I also collect the fruit that falls off the plan and the fruit growing on branches that have been severed from the plant. The plants grow taller than me, and finding all the ripe fruit requires crawling around under a canopy of tomatillo leaves, buzzing with pollinators.
Last year I grew over 30 pounds of tomatillos and this year I’m on track to grow a similar amount. Last week’s harvest was 6 pounds, and this week’s harvest 12. Over the years I’ve experimented with a variety of tomatillo recipes: I’ve pureed them raw, I’ve boiled them, I’ve sauted them, and I’ve roasted them. My current favorite recipe involves roasting all the vegetables together in 3-pound batches and pureying them in my blender. Here are some photos of the process, with the recipe at the bottom of the page.
So the next question is what do you do with 40 6-oz containers of tomatillo salsa? We put most of it in the freezer to eat all winter and share with friends. We used it to dip chips, put it on fish tacos, and use it as enchilada sauce. One of my friends said it made a tasty pasta sauce too. It has a tangy taste with just a small bit of heat (but of course you can make it hotter).
2 Anaheim, poblano or similar medium-hot peppers, seeded and sliced into a few strips
1-2 serrano or jalapeno peppers, seeded and sliced into a few strips (for spicier salsa use more, peppers, spicier varieties of peppers, or don’t remove the seeds)
½ to 1 bunch cilantro (1-2 cups)
1 teaspoon sugar
1.5 teaspoons cumin
3 teaspoons dried Mexican oregano (regular oregano can be substituted but reduce to 2 teaspoons)
½ teaspoon salt
¼ cup lime juice
Preheat oven to 500 degrees
Place tomatillos, garlic, onions, and peppers on 2-3 medium baking sheets and roast for about 20 minutes until tomatillos and peppers are charred and oozing juices. Make sure the garlic roasts between tomatillos so it doesn’t burn.
Take vegetables out of the oven and let cool for at least 10 minutes
Place roasted vegetables and all other ingredients in blender jar and mix on medium setting to chop, but not puree. Depending on your blender and how chunky you like your salsa you may be able to just run the blender for 5-20 seconds, or you may need to pulse it about 10 times. With my Blendtec blender I like to put in all the ingredients except the cilantro and blend for 5-6 seconds. Then I add the cilantro and blend for 5-6 seconds more.
Makes about 7 cups of salsa, which can be poured into about 10 6-oz containers and frozen.
This salsa is pretty mild. If you like it spicy add more hot peppers. This quantity will fit in a regular Blendtec Wildside+ blender jar but for many standard home blenders this is more than will fit. If you have a smaller blender jar, divide ingredients proportionally and blend in batches. It is easier if you blend each batch together with all its ingredients rather than try to mix batches together later (e.g. blend half the tomatillos, half the peppers, etc. in one batch).
We celebrated 10 years of our women over 30 recreational soccer club at a picnic this weekend and I gave a little speech…. Ok, it was kind of a long speech. Sharing for my soccer buddies who missed it, and for others who might be inspired to learn to play soccer or start their own soccer club.
It all started back in Spring 2013 at a Dynamo boys U13 end-of-season parents vs kids game. My son had played in the Pittsburgh Dynamo recreation league since he was in U6. Although I didn’t have much in the way of athletic skill, I always enjoyed the end-of-season parents vs. kids games, where the parents always let the kids win. But as my son got older, the kids were increasingly able to win without the parents going easy on them, and I watched as most of the moms stepped back and let the dads compete in the end-of-season game.
At the end of the Spring 2013 parents game I observed that soccer seemed like a fun sport, but it would be a lot more fun if I actually knew how to play. I chatted with some of the other moms on the sidelines and asked them if they would like to learn to play too. Some of them seemed interested. I was an age-level commissioner in the Dynamo rec league, so I reached out to the head rec commissioners and asked if we could have a soccer clinic for moms during the 2013 Fall season. My recollection is that the suggestion was met with some skepticism that anyone would actually show up, and a definite lack of enthusiasm to put effort into organizing it. But I was told that if I was willing to put together a proposal and be the one to organize it, the Dynamo board would consider it. Someone on the board mentioned they had heard of something similar in New Jersey and someone had written a book about it.
I’m not sure they actually expected that I would follow through. I didn’t know much about soccer but I know how to organize things.
And I tracked down the book, “Alive and Kicking: When Soccer Moms Take the Field and Change Their Lives Forever.” The book told inspiring stories about a group of soccer moms who learned to play soccer and formed a soccer league in Montclaire, New Jersey in the late 1990s. These women approached the director of a for-profit youth soccer camp to organize soccer clinics for them, and their clinics were largely coached by men. In addition, when an indoor soccer dome opened, the soccer moms quickly organized themselves into teams. The teams got very competitive very quickly, encouraged by their male coaches, and also by some very competitive women organizers who started bringing in 20-something au pairs and other younger women to help their teams win. Not too surprisingly, both bodies and feelings were regularly injured, and the group had to split into divisions with different levels of play. I liked the initial idea the New Jersey moms had for soccer clinics, but was hoping for something less competitive, so I decided from the beginning to set a minimum age of 30 to participate and to try to find female coaches.
I drafted a proposal for “Dynamoms,” which I described as having the purpose of providing “opportunities for mothers and other female role models of Dynamo youth players to learn about soccer, improve their skills, and have fun.” I also argued that “besides promoting fitness and fun,” Dynamoms would help mothers become “more comfortable with their soccer skills” and thus “they will be more willing to step in and assist with their kids’ soccer practices as needed, referee games, practice kicking soccer balls with their kids, or even volunteer as coaches.” As Dynamo was struggling to sign up enough middle school girls to field rec teams at the time, I added, “This may also encourage more girls to stick with Dynamo soccer longer. Having more girls playing Dynamo soccer supports the league’s mission, and having more mothers volunteering as coaches benefits the league as a whole.”
I talked to a friend who had coached Dynamo teams and played in an adult soccer league herself. She agreed to lead the Dynamoms clinics and we settled on holding three 90-minute clinics during the Fall season on the Schenley Oval grass at 5:30 pm, which was at the same time the Dynamo U16 rec teams played on the turf. We decided to spend 45 minutes each week on soccer skills and then split into two teams for a scrimmage with a referee. I created a budget and convinced the Dynamo board to let us give it a try if I could find at least 10 women who would pay a $50 registration fee. The board agreed. But then my friend ended up moving to another city that summer and I needed to find other coaches.
I talked to Courtney, who had coached my son’s rec team as a volunteer, and offered to pay her to coach a group of moms. Someone on the board suggested reaching out to Julie, a mom who coached a Dynamo team and had played college soccer. Courtney and Julie agreed to coach. I designed a black t-shirt based on the Dynamo logo with “ms” appended to the end, added Dynamoms to the Dynamo online registration system, and sent an email to all the Dynamo parents. We quickly exceeded the minimum 10 women needed, and in the end I believe about 40 women signed up, far exceeding my expectations.
Our Fall 2013 clinics were a lot of fun. As I recall, we were all terrible soccer players, but the coaches were patient with us and we did at least mostly listen to them and try to do their drills. When we scrimmaged the play stopped frequently because we all had lots of questions we wanted to ask about the rules of soccer. By the end of the three sessions, about half the women who participated had concluded that soccer was not for them, but the other half loved it and wanted to know when our next season would start and “could we do this every week?”
Not wanting to wait six months until April for more soccer, we decided to organize an indoor season that would start in January. I knew nothing about where one could play indoor soccer in Pittsburgh or how to rent a gym, but the enthusiastic soccer moms had suggestions. Kitty suggested renting the gym at the Ellis School, and on Saturday afternoons in January and February we held Dynamoms indoor clinics. Then in April 2014 we had a full 8-week outdoor season. Dynamoms had become a thing.
Along the way we had a minor crisis when members of the Dynamo board, who hadn’t actually expected Dynamoms to take off, started wondering whether Dynamoms actually fit the mission of a youth league and whether we would be covered by Dynamo’s insurance. We resolved the insurance issue and the board agreed to let us continue.
Somewhere along the way I hired Rebecca, one of my PhD students, as a third coach. When Rebecca and Julie moved away in the same summer we searched for coaches again and ended up hiring two younger women with soccer skills. They were good coaches, but some of us were old enough to be their mothers. When they moved on we recruited some of our more skilled players to become coaches.
We also had to find alternate gyms for indoor soccer after Ellis stopped renting their gym. We played for a couple of years in a tiny gym on the top floor of the Beth Shalom synagogue, and then for several years in the gym at the Sterrett middle school.
Another great thing that happened along the way was pickup soccer. Some of the women started asking about having games before our season started and after it ended. Some wondered whether we might play on a weeknight in addition to Saturday afternoon. And people other than me started organizing pickup games. Beth took the lead on pickup, finding fields, announcing when the games would be, and making sure we had a bag full of pinnies.
We adopted the Dynamo recreation league rule of not keeping score. As Deanna likes to say, the score is always “rainbows to unicorns.” And Kitty reminds us “The stakes cannot be lower.”
By the time the COVID 19 pandemic started in spring 2020, Dynamoms had been around for over 7 years and had settled into a pattern of 8-week fall and spring seasons on Saturday afternoons, 8-week winter indoor seasons on Sunday afternoons, and Wednesday night or Saturday afternoon pickup games whenever the weather was conducive. We typically had between 20 and 30 women sign up for each season, and a dozen or so would show up for a pickup game.
When schools and workplaces rapidly shutdown in March 2020, we initially discontinued our pickup games. But as we learned more about ways to reduce the risk of COVID transmission, and at the same time became more and more desperate to get out of our houses and interact with other grown women, we developed COVID rules and resumed pickup games. Jynene, who is a nurse, advised us on how we could play soccer safely during a pandemic. We brought our own light and dark shirts rather than sharing pinnies, we tried to social distance and stay six feet apart from each other, and we all wore masks. As we played pickup soccer through the summer, other women walking by our games asked to join us. Our numbers increased, and we added more games, until we were regularly playing three times per week. And the more we played, the more women asked to join us.
Winter came and we kept playing. Indoor soccer was not going to happen due to COVID so we had to keep playing outdoors. It was cold outside, but we soon realized that if you bundle up with lots of layers to warm up, once you start moving on the soccer field, you can shed your outer layers and most of us were playing comfortably in a single layer shirt, joggers, gloves, and a hat, in below freezing temperature.
The only thing that could stop us was the snow. The first time it snowed during the pandemic, we started emailing each other. What was the field like? Someone went to the oval to take a photo of the snow-covered turf. It didn’t look like we would be able to play. Fortunately, the snow melted quickly and we were soon back to soccer. But then it snowed again. After a couple of small snow storms, someone suggested that snow was nothing that 20 determined women with snow shovels couldn’t handle. So we arrived for our usual pickup game, snow shovels in hand, and shoveled enough of the Schenley Oval turf to have a small game.
It turns out this was a service to other soccer players too, and we noticed other groups using our shoveled area. Some of them sometimes enlarged our field or created a second one nearby. As the snow got deeper we developed some new rules. If the ball hits a snow bank and bounces back into the field, play it. If the ball lands in the snow, whoever retrieves it gets the ball, regardless of which team kicked it out. This led to some friendly races through the snow to get the ball. Snow rules brought a whole new dimension to the game.
One day while shoveling, Kitty remarked that it would be really fun if we could all get together in warmer weather and have a soccer camp. We all agreed and kept shoveling, but I’m not sure any of us except Kitty thought it would actually happen.
In spring 2021 we resumed our Dynamoms clinics, still wearing masks and practicing social distancing. And Kitty brought up the idea of soccer camp again. She had ideas for venues, she was looking at dates. We realized she was serious. Kitty organized an adult women’s soccer camp for us at Raccoon Creek State Park. The cabin rentals were super cheap, but the accommodations were quite rustic, full of spiders and mice. The toilets didn’t flush and the showers didn’t drain. But despite the rustic accommodations, we had a blast.
Soccer camp 1.0 was such a success that Kitty decided not to wait another year and immediately began searching for better accommodations for holding soccer camp 2.0 in the fall. We found wonderful camp facilities at Camp Soles and we’ve been going back there twice per year ever since. We’ll have soccer camp 6.0 in September with lots of soccer joy, camp fires and other camp activities, dance parties, euchre, beer soccer, and more.
And in a case of life imitating art imitating life (or something like that), our second camp shirt was designed by Pati (AKA Professor Haute), who was also a character in a romance novel about a soccer team very similar to Dynamoms that was written by one of our players. The real Pati produced camp shirts that resembled a shirt worn by the fictional Pati in the book.
Now we no longer have to wear masks and practice social distancing, and fingers crossed that doesn’t change. And our clinics have gotten more popular than ever. Last spring 69 people signed up for our soccer clinics, and we are well on our way to those sorts of numbers for our Fall season.
As we’ve grown, we’ve encountered a few growing pains. We used to let men play pickup with us if they asked nicely and agreed to play by our friendly rules. But when too many men showed up for a game, it really changed the character of the game and made people worry about injury. We had a meeting to discuss and we decided to prohibit men on “Women Wednesdays” and allow a limited number of “man spots” on Mondays. Later, we decided to only let women play unless we had a shortage of players, and to strictly enforce the 30+ rule.
When we started 10 years ago, we used the Dynamo youth permit for our clinics, and didn’t worry about permits for pickup games. But as more groups have started to use the Schenley Oval and the city changed their field use policies, we had to start paying for our own permits and often found we had trouble getting field space if we showed up without a permit. I have learned more than I ever thought I would about getting field permits and I have names and numbers of a whole slew of other field users that I have negotiated with over field space.
Over time, running Dynamoms has become increasingly time consuming and complicated. So earlier this year I asked people to volunteer to be part of a Dynamoms Coordinating Committee (the DCC) to help spread the workload around. I was pleased to get a whole bunch of volunteers, and now we have a committee of 12 of wonderful women sharing the work of running pickups, obtaining permits, maintaining the mailing list, running the registration system, ordering t-shirts, and more. Sometimes having a committee can be a little frustrating because we all have opinions, and we are all very respectful of listening to other peoples’ opinions, so we are sometimes hesitant to do anything until everyone has weighed in. But we’re learning how to work together more efficiently and make decisions and get things done. And if any of you would like to volunteer to take over my job as the Dynamoms Commissioner, please let me know. I’ll keep doing it for a while but would be happy to make plans to turn it over to someone else.
One of the difficult decisions the DCC has struggled with is whether to keep the name Dynamoms or change to something more inclusive, considering that a large number of our players are not actually moms. After much debate, a big survey, and more debate, we were unable to find one name that satisfies everyone, so we decided we would just use two names. Thus, we are now the Pittsburgh Dynamoms Football Club, as well as Pittsburgh DFC. Everyone can choose what they want to call it and which t-shirt they want to wear.
So now, as we enter our 10th year of Dynamoms/DFC soccer, it is hard to believe we have come this far. Who would have thought three clinics for soccer moms who didn’t know how to kick a ball would turn into a football club with over 100 members with well-attended clinics, camps, and pickup games 2 or 3 times per week year round? We’ve inspired some of our members to coach their kids’ teams and some of them to travel to Australia to watch the women’s world cup. Dynamoms has sparked many new friendships, social events, and support for our members when they need it. A large number of our members are professionals in a diverse set of fields. There’s a group who, like me, are professors. There are teachers, doctors, nurses, lawyers, social workers, photographers, bakers, designers, non-profit leaders, romance novelists, small business owners, and stay-at-home moms. It’s been fun to learn about what everyone does when they are not playing soccer, as well as some of the more unique interests people have. Bee keeping. Pet portraits. Sexy bird legs?
I want to close by just remarking on what Dynamoms had meant to me personally. I joined a recreational soccer team in first grade. My lack of athletic skill and a bully on my team insured that my first season was my last. So when I started Dynamoms, I didn’t honestly know if would actually be able to play soccer.
But 10 years later, look at me now. Who would have thought that I would ever own a pair of adult soccer cleats, let alone 5 pairs – like I needed another excuse to buy more shoes! Who would have thought that I would take time off of work and abandon my family for three days to go to soccer camp twice a year?
When we play a soccer game, you can see that some of our players are really good. Some of them played a lot of soccer as kids and in college. Some of them came to soccer later in life but picked it up very quickly, generally because they were experienced in other sports. They run fast, their kicks are accurate, they can readily intercept balls. And then there are the rest of us.
When I started playing with Dynamoms I had pretty much zero soccer skill. I was worried that everyone would figure this out pretty quickly and then nobody would pass the ball to me. But that didn’t happen. People passed to everyone, including me, and over time, I was able to successfully receive some of the passes that were sent my way. People cheered me on when I ran after a ball that was just out of my reach, and congratulated me when sometimes I actually stopped it before it rolled out of bounds. I’ve learned that when one of the better players has the ball, I can pressure them, and while I can’t usually steal the ball from them, I can slow them down and force a pass. And occasionally when I do steal a ball, it feels really good. I can kick the ball with both my left foot and right foot now, and can competently play both left and right wing and pass the ball to a teammate in the center of the field. I still feel completely awkward playing in the center of the field myself, I can’t boot the ball all that far, and I have trouble running and communicating with my teammates at the same time. I still have a lot to learn, but hopefully I have many years of soccer ahead of me.
I would like to personally thank all of you for being so supportive of me and everyone else who comes out to give soccer a try. I love you all! It’s been a great 10 years and I’m looking forward to many more!
My college-student brought home a pile of jeans that mostly fit her but gap at the waist. She asked if I could fix them. I asked the Internet and found a number of complicated solutions. Then I found a really easy solution involving elastic. My daughter was skeptical but agreed I could give it a try on one pair. I mostly followed the instructions and It worked so well she brought me several more pairs to de-gap. I have a few pairs of my own jeans that will likely get this treatment too.
The technique takes advantage of the fact that most pants waist bands are basically a tube that goes around the entire waist. There is an inside and an outside and empty space in between. I have previously improved the fit of several pairs of yoga pants by opening up the side seam on the the inside of the waistband and threading elastic all the way around, and sewing the two ends of the elastic together. For jeans, you just need a piece of elastic across the back. So the problem is what to attach it to. The solution is to sew the elastic to the waistband under a belt loop so it is hidden. (Even if you don’t sew it under a belt loop, if you use thread that matches the jeans it is not going to really show. And of course, if you wear a belt, it is not an issue at all. But one of the reasons to add the elastic is so that you do not need a belt to hold your jeans up.)
Most jeans do not have a convenient side seam as the inner waistband is a continuous piece (although one of the pairs of pants my daughter brought me were actually pants, not jeans, and they had a convenient seam that I popped right open with my seam ripper). So for the jeans, I just used a small sewing scissors to cut a little vertical slit through the inner waistband, positioned right under a belt loop on each side of the back.
Then I used a safety pin to thread elastic inside the waistband between the two slits.
I trimmed the elastic, leaving the waist bunched up a bit (it will smooth out when you wear the pants). I pinned the elastic a bit inside each slit so it wouldn’t pull out while I sewed. (Yes I know the photo below is from a different pair of jeans than the one above, but trust me, I did the same thing on all of them.)
Then I used my sewing machine to sew a wide zigzag over the slit, holding the belt loop out of the way so it didn’t get caught in the stitches. I did this for both slits and removed the pins.
Now her pants fit and the stitches holding the elastic in place are hidden under the belt loops.
A few weeks ago I made a Sinclair Serena dress to try out the pattern, which I plan to use to make a fancy gown. The pattern worked out pretty well in double-brushed polyester, but I’m planning to use a fancy (expensive) custom-printed crushed stretch velour fabric for the gown, so I decided to make the pattern again with some cheap velour. I bought two yards of purple crushed panne velour from Cali fabrics for $4.99 a yard. This fabric is pretty and has similar stretch as the fabric I plan to use, but it is not as soft and doesn’t feel quite as nice. It is also not really purple – I would call it lavender, but it is not the royal purple shown on the website. This is not meant as a high-end fabric, but it is fine for a muslin.
I projected the pattern and cut out the velour. I decided to use a purple ITY fabric for the lining pieces. Then, throwing caution to the wind, I decided to sew the dress together using my brand new Serger, having never serged before. It actually wasn’t that hard, except for the fact that velour is a super slippery fabric and no amount of pinning could get it to hold still. The slippery ITY lining just made it worse. There are parts of this pattern that call for two layers of regular fabric and 2 layers of lining, and getting them all lined up to complete the jigsaw puzzle bodice was a real challenge. I eventually basted together the layers before sewing, and it was fine. But parts of it that I sewed early on are not quite lined up right, although I managed to mostly hide them. Note to self when I make the gown, plan to do a lot of basting.
Besides being very slippery, the velour as almost no vertical stretch. That doesn’t seem to be a problem with this pattern, other than reducing the ability to ease out mistakes. Somehow the back ended up being and inch longer than the front when all was said and done (I’m pretty sure it was cut correctly, but there were numerous sewing errors), and I ended up just trimming it before hemming.
I did make a few mistakes that are mostly attributable to learning how to use my serger while making this dress. I now have a full understanding of the knife function and how not to use it when turning a corner. Repairing some of these mistakes might be one of the reasons the back ended up longer than the front.
I did manage to fix some problems from my last Serena dress. This time I added clear elastic to the neckline for good measure, and I sewed the crossover all the way to the edge. With both of these improvements, there is no possibility of drooping. I also did a better job stretching the armhole bands around the curves, so they look better than last time. In order to reduce pocket flapping,I made the pocket bags a little slimmer and attached them to the skirt a bit higher than the pattern calls for – about 1 inch below the point where the skirt meets the bodice. I made the pocket openings a bit smaller to keep my phone from falling out. I used the velour for the back pocket bags and the lining for the front to reduce bulk. But the lining still peaks out a bit so I may just use the velour for both sides next time.
The good news is that the whole dress did end up coming together nicely. The proof of concept worked and the muslin is a dress I would actually wear in public. In fact I wore it to an outdoor theater production this evening and can report it was both stylish and confortable.
I’ve been pondering buying a serger ever since I started sewing lots of knit clothing a year ago. I didn’t take the plunge because I have a really nice (somewhat high-end Bernina) sewing machine, I couldn’t decide which kind of serger to buy, and I was also worried about the learning curve. But so many people rave about them and they seem to save a lot of time… and I figured how hard could it be.
My first dilemma was whether to buy a combo serger and cover stitch machine or just a serger. If you don’t know what i’m talking about look at your favorite t-shirt. Chances are most of the seams have thread that wraps around the seam in sort of a zig-zaggy pattern. That’s done with a serger. If you look at the hem at the bottom of the shirt there are probably two lines of stitching on the outside. That’s done with a cover stitch machine. You can fake both of these things on a regular sewing machine, but not really well. The idea of a machine that can do both serging and cover stitch is appealing — there’s only so much space I have in my sewing room to collect more machines. But as I started reading up on combo machines I saw that many sewists who had them said that it was too difficult to switch them between serging and cover stitch mode, so most of them left them in serging mode and never switched to cover stitch — and then some of them went out and bought another machine for cover stitch. Since combo machines are more expensive than plain old sergers, I decided to just go with the serger and consider buying a cover stitch machine later.
There is a pretty big price range for sergers, from a couple hundred dollars to thousands of dollars. The expensive high-end sergers are very fast and can thread themselves. Self threading (often referred to as “air threading”) is nice because sergers typically have four threads (some have more) and they are notoriously difficult to thread. So I was pretty excited about the idea of a self-threading serger, but I wasn’t sure I was ready to invest in one given that I have never used a serger of any sort. Looking at the low-end sergers, the Brother 1034D and 1034DX seem to have great reviews and are frequently recommended on lists of best Sergers for beginners. They are at a low price point (around $275) and they have a color-coded threading system that makes the complicated task of threading slightly easier. When I asked on Facebook what type of Serger I should get, two of my friends mentioned they had 1034DX sergers. But one concern I saw in the reviews is that they don’t handle thick fabrics like fleece well. I don’t know how much fleece sewing I will do, but when I saw that for $100 more I could get the Brother ST4031HD, I decided to go for that one. ST stands for “strong and tough.” It is almost identical to the 1034D except that it is built to handle thick fabric and it has an extension table, both of which were features I thought I could use. So I ordered a Brother ST4031HD on Amazon and it arrived two days later.
Having never serged before, I was still a bit intimidated to use my new serger. I took it out of the box, registered it, and watched all the videos provided on the Brother website (note that it claims to come with a DVD with the videos, but they don’t seem to send the DVD any more; but they are all on the website, although not that easy to find). Finally I gave it a try with some scrap fabric and adjusted the differential feed to work with knits. So far so good. It sews very fast, but it didn’t take too long to get the hang of it.
The next challenge was threading the serger. The machine comes pre-threaded with color-coded thread to show you how to do it, but that thread won’t last long, and you probably don’t want to use a rainbow of thread on all your garments. I bought four large spools of medium grey polyester thread and worked on threading. I decided to use the easy approach, which is to cut the existing thread and tie it to the new thread, and carefully pull the new thread through the machine. This was much easier that figuring out all the threading details, but even this approach was not easy. Each time the thread stopped pulling I had to figure out where the knot was stuck and gently ease it to the next spot without breaking or jamming the thread. I figured it out and got it threaded, but was glad I chose grey thread, which will likely work with most sewing projects and maybe won’t need to be replaced for a long time. Later when I broke a thread I did have to watch the threading video so I could rethread the lower looper.
I had a stretch velour dress cut out and ready to sew, so I decided to take the plunge and serge it. In hindsight, stretch velour was probably not the best fabric to start with as it is very slippery, and should have been basted before sewing. Nonetheless, I jumped right in and it mostly worked out ok. A few seams slipped so much that I had to go back and baste them and then resew them. I also learned the hard way how to lower the cutting knife and why you might want to do that. By default, sergers include a cutting knife that trims the fabric before sewing it. This is great, but it does mean you can accidentally cut your fabric in places you don’t want it cut. I did fine until I got to a point where I needed to pivot around an inside corner. I sewed to the point of the pivot, put my needle down to pivot, and then realized that the knife is in front of the needle and thus had already made a cut into the fabric where I didn’t want it. Fortunately, I was able to repair that problem and it was a good excuse to figure out how to lower the knife. I can see for some projects it is probably best to sew the whole thing with the knife lowered.
My serger has two other feet and all sorts of adjustments I haven’t tried. But the test run went pretty well and I’m excited about how fast it is to sew knits. Typically when I sew knit clothes I sew every seam twice: first with a narrow zigzag stretch stitch, and then with a wider zigzag that serves as a fake overlock. Both of these stitches take longer to execute than a simple straight stitch because of the side-to-side motion. With a serger I can sew each seam with one pass instead of two, and that one pass is faster than either pass with my regular sewing machine.
October 8, 2023 update — One minor issue I’m having with this serger is that I keep pressing down on the extension table and popping it out of place. I was able to solve this problem by cutting a board 3-3/8 inches tall and 8 inches long and sliding it under the table.
I love the Sinclair seeing all the things people make and post to the Sinclair patterns Facebook group. It’s exciting when a new pattern comes out and all the testers post what they made over the first few days. There are some sewists who seem to test every pattern, and many of them make several versions when a new pattern comes out. I assume they don’t have the sort of day job that I have, and maybe they sew faster than I do. Or maybe they have a serger? Maybe I should get one? Anyway, I’m enjoying their posts and I feel like I’m starting to get to know some of the regulars.
I’ve been tempted by the last few calls for pattern testers. I’ve now sewn over half a dozen Sinclair patterns, so maybe I could get selected. But generally you have only 3 or 4 days to make the pattern, and that usually doesn’t fit my schedule. But when Sanna Sinclair announced the call for testers for their new Linda twist neckline knit top and dress pattern, I checked my calendar and saw that the timing might work. I filled out the application form and waited to see if I would be selected. Early Friday morning I got the email from Sanna Sinclair with the link to the test pattern, the private tester Facebook group, and a request to finish a garment and post fit pictures by Sunday evening.
By the time I got home from work on Friday, the first testers had already finished their tops and posted photos. I thought about getting right to work on mine, but first I had to finish sewing a pair of black Cleo palazzo pants (to match mine) that I promised my daughter. I got those done Friday night and selected fabric from my stash and decided to sew a top rather than a dress, as I was a little concerned about whether I would have enough time for a dress.
The pattern called for very drapey fabrics, so I selected a medium weight modal-spandex knit in turquoise. This was my first time sewing with this type of fabric. It is soft and stretchy like double-brushed polyester, but more breathable and a little less tightly knit. I think it has less body and a more fluid drape, which makes it a little bit harder to work with, but it is very comfortable to wear and it suited this pattern well.
On Saturday I projected the pattern on my fabric, cut it out, and began to sew. I periodically checked the Facebook group to see what other sewists were working on and their comments on the pattern. One small error on the pattern was caught early on and a clarification posted. There were concerns about a few fit issues, but otherwise people seems to be doing well with this pattern. The completed tops and dresses looked pretty good. I thought about making a dress instead of a top, but decided not to over reach on my first pattern test.
I followed the instructions without too many issues. Doing the twist itself was very easy, in part due to the short video provided with the pattern that demonstrates exactly how to do it. I had some trouble overcasting the flimsy fabric with my sewing machine and contemplated buying a serger. I think I will buy one as soon as I figure out which one. I had some pressing issues, again mostly due to this particular type of fabric, but eventually I got them sorted out. The sleeves were a tad too short and the length was a couple of inches too long. So I used a narrow hem on the sleeves and chopped off some of the length before hemming the bottom. I observed the same problem with the keyhole flopping open as everyone else in the Facebook group, and followed the advice to hand stitch it closed. I posted my feedback and my V1 fit photos. All of these problems have been corrected in the final pattern so you shouldn’t have these any of these problems.
Monday morning Sanna posted her comments on our feedback and her plans for adjusting the pattern. She announced that V2 would soon be available the next day but said it was fine to take final photos of our V1 creations. So I put on my new shirt and asked my husband to snap some photos. When I got home from work I selected my favorite photos and uploaded them. I had a busy week at work and did not have time to make a V2 top, let alone a dress. But I enjoyed watching the Facebook group and seeing the sewists who had time to create several garments from this pattern over the course of the week.
I usually like to wear twistneck tops. I had a couple of ready-to-wear dresses with twistnecks, and found I kept futzing with and repositioning the twist as they never seem to lie perfectly right, and I just can’t leave well enough alone. I have to admit I did my share of futzing with this one as I was sewing it. But once I got it set I let it be and it stayed put. Then my husband washed it and called me over as he pulled it out of the dryer because he thought the twist had gotten messed up. But it happily popped right back into position. I expect with a more substantial fabric it would not have popped out at all. I will probably make more of these some time (maybe in ITY, double-brushed polyester, or cotton lycra). I love some of the results other testers got sewing this pattern with prints. I still love the simplicity and fit of the Bondi top and think that style works better under sweaters and blazers since it is smooth and symmetrical. But Linda is a cute top for wearing on its own that looks more elevated than a basic t-shirt, but is just as comfortable to wear.
This morning was the pattern launch and I was excited to see that the first two photos on the Linda pattern web page were mine!
It was fun to be a pattern tester and if Sinclair does another test at a time when my calendar is relatively clear I will definitely sign up to do it again. Also, this is such a good excuse for keeping more fabric than I really need on hand… these testing opportunities come up quickly and there isn’t time to shop for more fabric on short notice!
My resident teen daughter liked my Cleo PyLos LiKnit Palazzos so much she requested her own pair. They meet all her criteria for pants: feel like yoga pants, pockets, flowy, and black (she hates wearing jeans). She tried mine on and said she just needed them longer with a higher rise and they would be perfect. So that’s what I did. She put them on so I could take a photo and decided to wear them to her band gig.
And here we are wearing all our me-made clothes. I’m wearing my self-drafted cups dress and my daughter is wearing the muslin top for her vintage sundress with her new palazzo pants.
I saw the Sinclair Serena crossover knit dress pattern a while ago and was a bit intimidated about sewing the crossover part, which is a bit of a jigsaw puzzle. But I recently was looking for a knit dress pattern that would look great in a full length formal gown, and Serena looked like it could be adapted for this purpose. The gown project will be another story for later, but in the mean time I thought it prudent to sew a short version of this dress with inexpensive fabric to make sure this was going to work. So earlier this month I projected, cut, and sewed Serena in one weekend. Serena is an old pattern without projector files, but I was able to create projector files with pdfstitcher. [Correction: There are projector files, I just some how missed them!]
I used the 4 petite pattern and cut the skirt 1 inch below the above-the-knee length, making it sit exactly at the knee on me. I selected a floral double-brushed polyester for this dress. This is a light-weight, stretchy, and inexpensive fabric that’s very comfortable to wear. I looked at photos from others who have made Serena and saw some interesting approaches to color blocking this dress that really highlight the crossover (and/or the bust) and the jigsaw puzzling involved, but my favorites were all made from a single fabric print without any color blocking. Without the color blocking, you an hardly see the crossover, but you still get a lovely fitted top with a skirt that hangs from a point that I think will work really well for a gown.
Of course I made it with the pocket option (and added about an inch to the bottom of the pocket bags to make sure my phone doesn’t fall out of my pockets)! The pockets are great, but I think the openings sit a little low so in the next dress I will probably raise them about 2 inches higher. The pockets flop around when filled since they aren’t attached to anything except the side seams since there is no waistband to attach them too (and even if there was I probably wouldn’t attach them because I don’t like it when pockets distort the waist band), but I think they would flop less if they were attached higher. My favorite dress pockets are still the Alana dress pockets — no flopping or distorting — but that style of pocket only works with princess seams, alas.
The jigsaw puzzle was not actually too difficult to solve, although I do recommend reading the pattern tutorial very carefully and watching that you don’t try to assemble any of the pieces upside down or backwards (I had a couple of close calls). The pattern suggests optionally adding some elastic to the top edge of the v-neck if it doesn’t recover well from a stretch. I tested the recovery as suggested and it seemed fine, so I did not add the elastic. I have a very slight droop in the top layer of the crossover that might have benefited from adding the elastic, or at least a bit of fusible knit interfacing (maybe next time!), but it is subtle. (Later I realized that I actually ended the seam that holds the crossover down too early. Had I brought the same all the way to the center of the crossover it might not have drooped.) There is also optional top stitching that I opted out of, with no regrets. The arm holes are finished with a binding that I didn’t do a great job of attaching, especially on the left side, so the bottom of the armhole flops out a tad. Next time I will need to take more care with positioning and stretching the band. Most of these are issues that probably nobody would notice except me.
Anyway, I’m quite pleased with Serena, and am already planning to make another one soon.