If you haven’t read Part 1, read that first, and when you’re done with this read Part 3.

Ready for a bigger challenge, I decided to make a pair of pocket leggings out of the tartan Spoonflower sport Lycra. I selected the Sinclair Flex No Front Seam Leggings pattern in size 4p. No front seams meant no worries about matching plaids in the front: all I needed to do was center the main front leg pattern piece on a vertical line in the plaid. Of course, then I had to align the waistband piece to the main front pattern piece and figure out how to cut the two back leg pieces symmetrically and somewhat aligned with the front leg piece. I decided to use the color blocking option and make the side pocket pieces in a solid black 300 gsm QUAD performance jersey knit from Surge Fabric Shop to avoid any plaid matching issues. The QUAD fabric is a similar weight and composition to the sport Lycra, but has more stretch and a brushed side that feels really nice. I wish it came in more prints because I really like this fabric. I ended up using up almost all my remaining QUAD fabric, which was too bad because I accidentally folded down and trimmed the wrong pocket pieces. Since I didn’t have enough black fabric to recut those pieces, I carefully unpicked them and then sewed a small patch on the corners I had trimmed off. It’s not very noticeable unless you know where to look (in the black section just below the waistband in the back).

The leggings were more challenging than most of my other recent projects, in part because of the slippery plaid fabric, but also because the waist construction involves joining many layers. As I rarely pass up a pocket opportunity, I included the back waistband pocket (highly recommended by the pattern designer). Adding the waistband pocket was fairly quick and easy, but it meant an extra two layers to join when I attached the waistband to the rest of the leggings. I did most of the sewing on my serger, but had so much trouble aligning the waistband that I basted it on my sewing machine. Even then, it still didn’t align and I had to unpick and ended up hand basting and then finally serging. The pattern also calls for optional top stitching. I top stitched some of the seams with a zigzag on my sewing machine, but wasn’t super happy with how it looked on the plaid so I didn’t top stitch all of it.

In the end, the leggings came together, the plaid is mostly (though not perfectly) aligned where it needs to be, and the leggings actually fit me. I chose the high-waist option and they stay in place pretty well, even though I did not include the optional drawstring (because I like my leggings to fit tight without a drawstring). I think on my next pair of Flex leggings I might add elastic in the waistband fold for a little extra hold. Overall, I think the leggings look good. However, one disappointment is that when the sport Lycra stretches, a lot of white shows through between the printing (“whiteout”). Since the legging pattern is designed to stretch the fabric, it means the fabric is not so bright, especially in the hip area. You can see it looks l a lot brighter near the ankles, where it is not as stretched. I think if I had a rotated the pattern 90 degrees on the fabric the whiteout might have been reduced.

I was going to make a tartan sports bra to go with the leggings, but then the new Sinclair Wave Athletic Knit Tank Top With Waistline Shaping and Pockets pattern came out and I decided to make that instead. I paired the tartan fabric with a black polyester/spandex stretch mesh from Knitfabric.com for the front and back side panels. (I still have enough tartan fabric left over for a sports bra and maybe also some color blocking on bike shorts.)

I debated whether to go for a 4p or 6p and in the end decided to sew the Wave in a 6p because I prefer my athletic tops to be loose. I think the 4p could have worked but would have been tight across the bust. Next time I might grade the sides in towards the bottom. I used the scoop neck option with bands, the cutout back, and hemmed bottom. The cutout back is a super cute feature that is easy to make. I ended up not doing any top stitching except on the hem and cutout.

Putting the wave pieces together is a little bit like assembling a puzzle, but it all worked out ok. My main frustration was with the Spoonflower sport Lycra fabric, which is slippery and doesn’t press easily. It made the bands and curved hem more painful to sew than they should have been. I did reasonably well with the plaid matching on this one, and even aligned the plaid on the top with the plaid on the leggings, although the top is darker because it doesn’t get stretched as much.

This is a top I will workout in, but it also looks great with jeans. I like the fact that there is enough shoulder coverage that this can be worn with a regular bra or a racerback, and it offers more sun protection on the back than a lot of sleeveless sports tops.

Because I don’t know when to stop and you can never have too much tartan, I made a headband to match and now I have a totally tartan athletic kit! I love the pockets in the leggings and the fact that the black panels on the top align with the black pocket panels on the leggings. I wore the leggings a few weeks ago in the Carnegie Mellon “Random Distance Run” and will certainly wear the entire outfit for future CMU races.