I have previously made quite a few long-sleeve knit shirts using the Sinclair Bondi pattern, which I like quite a bit and I think fits me really well (especially after I made a few minor adjustments). However, it is fairly fitted and I don’t think it works as well for fabric that doesn’t have a lot of 4-way stretch (although that hasn’t stopped me from using it with less stretchy fabrics, sizing up a size). For example, I noticed a lot of drag lines in the back when I used it with a low-stretch light-weight wool. Allure is semi-fitted, slightly less fitted than Bondi, so I thought it might work better for low-stretch jersey fabrics. When I put the two patterns on top of each other I could see that the Bondi size 6 and the Allure size AU10 are about equivalent. The Bondi is more fitted in the waist, flares out more at the hem, and is wider across the bust in the front. I normally make Bondi in size 4P, but size up to a 6P when using low-stretch fabric.

First, I made a plain-sleeve Allure in size AU10 from a lightweight 150 gsm, ginger-red hand-washable wool jersey knit fabric from Knitfabric.com. The fabric was advertised as having 25% stretch in each direction, but it seems to me it has more like 50% horizontal stretch and <25% vertical stretch. I used about a yard-and-a-half of 43″-wide fabric. I cut the hem about 3.5 inches shorter than the regular length, which is a good length on me for wearing a shirt untucked (which is mostly what I do), but long enough that I can tuck it in if I want to. I also did a sloped shoulder adjustment and shortened the sleeves by 1inch. I wanted a scoop neck, but knew from my previous Allure that I wanted it a little higher. So I used the front neck line from the Wanderlust dress high scoop neck and adjusted the size of the neckband accordingly. I hemmed the bottom and sleeves with a shallow zig zag stitch on my sewing machine after first folding and pressing it with knit stay tape.

I mostly liked the way this came out, but found the neckline still a little too low and wide in the front and too low in back for my taste. so for my next top, made from dusty olive cupro jersey from Surge Fabrics, I raised the front neckline about .75 inch and brought the sides in about .5 inch. I also brought the back neckline in about .5 inch and raised it to the same height as the back of the crewneck — similar to the “screwp neck” that I like with the Bondi pattern. I used less than a yard of 58″-wide fabric. This jersey cupro is 180gsm and advertised as having about 50% horizontal and 25% vertical stretch. The vertical stretch seems to me less than that. The fabric color is almost grey — the olive is very dusty. None of my green threads were a good match for this fabric so I ended up using steel grey. The curpo fabric is 65% modal and 35% poly and does not require any special care. It has a very silky feel. I coverstitched the hem, sleeves, and neckline with the steel grey thread.

The neckline came out exactly the way I wanted it on this one after I futzed with the length of the band (I basted it on, decided it was too tight, removed it and cut another one 1.5 inches bigger). But overall the top was too tight. I learned from past experience with a cupro jersey dress that it doesn’t stretch much and fits tight. The sleeves were uncomfortably tight on me. But I thought it would still work in this semi-fitted pattern. But it was too tight and had lots of drag lines. And when I raised my arms and put them back down the shirt stayed bunched up around the bust. It took less than a yard of fabric and I had started with two yards, so I decided to try again.

I made another Allure from the dusty olive cupro, this time size 12. I also added a .75-inch broad shoulder adjustment, in addition to the sloped shoulder adjustment — an adjustment I usually make with Bondi too. I used the screwp neck, shortened the hem by 3.5″ and shortened the sleeves by 1 inch.

This time the fit was very good. However, you can still see some drag lines at the shoulder, I think due to the lack of vertical stretch. I will definitely size up if I use this fabric again.The cupro fabric is an easy-care soft and silky fabric and has a nice drape, but it also seems to stick to itself and doesn’t smooth itself out without help, as you can see in these photos. We got the last photo below after a lot of smoothing. I think this is lovely fabric, but it doesn’t seem to work that well for a semi-fitted t-shirt. I think it works better in a dress because there is weight pulling it down. I think it would also work better with princess seams, in an oversized style, or even with a woven pattern.